Room Modes in an 11x26 ft Room with a 9 ft Ceiling
A 11 by 26 ft room with a 9 ft ceiling suits a dedicated home theater or media room. Its lowest room mode sits at 21.6 Hz, set by the 26 ft length, the lowest note the room itself reinforces before any speaker or sub plays a thing.
Checked against every mode below 200 Hz, this room scores 50/100, a rough score, worth planning around. The clearest issue is that two of its dimensions reinforce the same note near 151.5 Hz.
Mode spectrum
5 dense clusters (≤5 Hz apart) — overlapping resonances are harder to treat evenly.
Each line is one standing wave. Axial modes, the strongest kind, stand tallest; tight bunches and wide empty stretches are where the bass will sound uneven.
Axial modes by dimension
| Dimension | 1st | 2nd | 3rd | 4th |
|---|---|---|---|---|
| Length (26 ft) | 21.6 Hz | 43.3 Hz | 64.9 Hz | 86.6 Hz |
| Width (11 ft) | 51.2 Hz | 102.3 Hz | 153.5 Hz | 204.6 Hz |
| Ceiling height (9 ft) | 62.5 Hz | 125 Hz | 187.6 Hz | 250.1 Hz |
What this means for your room
- The lowest room mode is 21.6 Hz, set by the 26 ft length.
- Your 26 ft length and 11 ft width both resonate near 151.5 Hz, so bass at that note will be much louder than its neighbours.
- Your 26 ft length is almost exactly three times your 9 ft ceiling height, so their modes fall close together without quite stacking.
- Between 21.6 Hz and 43.3 Hz there are no modes at all, so notes in that 21.7 Hz gap will sound thinner than the bass around them.
- Mode density drops in the 25 Hz third-octave band (0 modes against 1 in the band below), so bass will sound uneven from note to note.
- The proportions (1 : 1.22 : 2.89) fall outside the Bolt area because the room is long and narrow for its height, so modes bunch up along the length.
- Below about 148 Hz (the Schroeder frequency) individual modes shape the sound; above it, reflections and reverb matter more.
The modes from your 26 ft length and 11 ft width land on top of each other near 151.5 Hz. That stack means one specific low note gets reinforced twice, so it jumps out over everything nearby.
For a home theater, expect that stacked note to color explosions and sub-bass hits unevenly rather than smoothly. For a music room, it means you cannot fully trust what you hear in the low end at the listening position, since a note that sounds loud in the room may be perfectly balanced on the recording.
The proportions (1 : 1.22 : 2.89) fall outside the Bolt area, the range room ratios usually spread modes best over, because the room is long and narrow for its height, which bunches modes up along the length. That does not rule the room out, but treatment is doing more of the work here than shape is.
How to fix it, in order
- Start with bass traps in the four floor-to-ceiling corners; every mode in this room peaks there, including the ones set by your ceiling height.
- Full absorption at 151.5 Hz would take about 1.8 ft of trap depth, well past what any room can fit. Fill the corners as deep as you reasonably can (6 to 12 in, with an air gap behind), then lean on a membrane trap tuned near that frequency, your seat position and a second subwoofer with EQ to tame the note itself.
- Do not sit dead-center on the 26 ft length. Start near 9.9 ft from the front wall, about 38% of the way back, and adjust from there.
- For the subwoofer, try a few spots before settling: a front corner usually gives the most output but also the most uneven bass, while pulling it off the wall or adding a second sub often smooths out peaks like the ones this room has.
- After treating, run an REW sweep from the seat. Everything below 148 Hz is where these modes live, so that is the range worth checking before you call the room done.
These numbers assume an empty rectangular 11x26 room with hard walls. Draw your real room, add furniture and speakers, and simulate the bass at your seat.
Every mode below 200 Hz
Below are all 94 modes this room produces under 200 Hz: 15 axial, 45 tangential, 34 oblique. Axial modes, which only involve one pair of opposite surfaces, ring the loudest. Tangential modes (four surfaces) come next, and oblique modes (all six surfaces) are the weakest of the three.
| Frequency | Type | Mode (length, width, height) |
|---|---|---|
| 21.6 Hz | axial | (1,0,0) |
| 43.3 Hz | axial | (2,0,0) |
| 51.2 Hz | axial | (0,1,0) |
| 55.5 Hz | tangential | (1,1,0) |
| 62.5 Hz | axial | (0,0,1) |
| 64.9 Hz | axial | (3,0,0) |
| 66.2 Hz | tangential | (1,0,1) |
| 67 Hz | tangential | (2,1,0) |
| 76 Hz | tangential | (2,0,1) |
| 80.8 Hz | tangential | (0,1,1) |
| 82.7 Hz | tangential | (3,1,0) |
| 83.6 Hz | oblique | (1,1,1) |
| 86.6 Hz | axial | (4,0,0) |
| 90.1 Hz | tangential | (3,0,1) |
| 91.6 Hz | oblique | (2,1,1) |
| 100.5 Hz | tangential | (4,1,0) |
| 102.3 Hz | axial | (0,2,0) |
| 103.6 Hz | oblique | (3,1,1) |
| 104.6 Hz | tangential | (1,2,0) |
| 106.8 Hz | tangential | (4,0,1) |
| 108.2 Hz | axial | (5,0,0) |
| 111.1 Hz | tangential | (2,2,0) |
| 118.4 Hz | oblique | (4,1,1) |
| 119.7 Hz | tangential | (5,1,0) |
| 119.9 Hz | tangential | (0,2,1) |
| 121.2 Hz | tangential | (3,2,0) |
| 121.8 Hz | oblique | (1,2,1) |
| 125 Hz | axial | (0,0,2) |
| 125 Hz | tangential | (5,0,1) |
| 126.9 Hz | tangential | (1,0,2) |
| 127.5 Hz | oblique | (2,2,1) |
| 129.8 Hz | axial | (6,0,0) |
| 132.3 Hz | tangential | (2,0,2) |
| 134 Hz | tangential | (4,2,0) |
| 135 Hz | oblique | (5,1,1) |
| 135.1 Hz | tangential | (0,1,2) |
| 136.3 Hz | oblique | (3,2,1) |
| 136.8 Hz | oblique | (1,1,2) |
| 139.6 Hz | tangential | (6,1,0) |
| 140.9 Hz | tangential | (3,0,2) |
| 141.9 Hz | oblique | (2,1,2) |
| 144.1 Hz | tangential | (6,0,1) |
| 147.9 Hz | oblique | (4,2,1) |
| 148.9 Hz | tangential | (5,2,0) |
| 149.9 Hz | oblique | (3,1,2) |
| 151.5 Hz | axial | (7,0,0) |
| 152.1 Hz | tangential | (4,0,2) |
| 152.9 Hz | oblique | (6,1,1) |
| 153.5 Hz | axial | (0,3,0) |
| 155 Hz | tangential | (1,3,0) |
| 159.4 Hz | tangential | (2,3,0) |
| 159.9 Hz | tangential | (7,1,0) |
| 160.4 Hz | oblique | (4,1,2) |
| 161.5 Hz | oblique | (5,2,1) |
| 161.6 Hz | tangential | (0,2,2) |
| 163 Hz | oblique | (1,2,2) |
| 163.9 Hz | tangential | (7,0,1) |
| 165.3 Hz | tangential | (6,2,0) |
| 165.4 Hz | tangential | (5,0,2) |
| 165.7 Hz | tangential | (0,3,1) |
| 166.6 Hz | tangential | (3,3,0) |
| 167.1 Hz | oblique | (1,3,1) |
| 167.3 Hz | oblique | (2,2,2) |
| 171.3 Hz | oblique | (2,3,1) |
| 171.7 Hz | oblique | (7,1,1) |
| 173.1 Hz | axial | (8,0,0) |
| 173.1 Hz | oblique | (5,1,2) |
| 174.1 Hz | oblique | (3,2,2) |
| 176.2 Hz | tangential | (4,3,0) |
| 176.7 Hz | oblique | (6,2,1) |
| 178 Hz | oblique | (3,3,1) |
| 180.3 Hz | tangential | (6,0,2) |
| 180.5 Hz | tangential | (8,1,0) |
| 182.8 Hz | tangential | (7,2,0) |
| 183.3 Hz | oblique | (4,2,2) |
| 184.1 Hz | tangential | (8,0,1) |
| 186.9 Hz | oblique | (4,3,1) |
| 187.4 Hz | oblique | (6,1,2) |
| 187.6 Hz | axial | (0,0,3) |
| 187.8 Hz | tangential | (5,3,0) |
| 188.8 Hz | tangential | (1,0,3) |
| 191 Hz | oblique | (8,1,1) |
| 192.5 Hz | tangential | (2,0,3) |
| 193.2 Hz | oblique | (7,2,1) |
| 194.4 Hz | tangential | (0,1,3) |
| 194.4 Hz | oblique | (5,2,2) |
| 194.8 Hz | axial | (9,0,0) |
| 195.6 Hz | oblique | (1,1,3) |
| 196.4 Hz | tangential | (7,0,2) |
| 197.9 Hz | tangential | (0,3,2) |
| 197.9 Hz | oblique | (5,3,1) |
| 198.5 Hz | tangential | (3,0,3) |
| 199.1 Hz | oblique | (1,3,2) |
| 199.2 Hz | oblique | (2,1,3) |
Questions about 11x26 rooms
- Will an 11x26 room work for a home theater?
- This size suits a dedicated home theater or media room, though the 50/100 modal score signals some work ahead, mainly because two of its dimensions reinforce the same note near 151.5 Hz.
- Where should I put bass traps in an 11x26 room?
- The four vertical corners first. Full absorption at 151.5 Hz would take roughly 1.8 ft of trap depth, so treat that note with a tuned membrane or pressure trap instead, and use thick porous corner traps (6 to 12 in) for everything above it.
- What subwoofer size is right for an 11 by 26 ft room?
- There is no fixed sub size tied to 286 sq ft; that number mostly sets this room's mode frequencies (94 of them under 200 Hz). At this size you will want more headroom than a small room needs, and two subwoofers usually beat one at keeping bass even from seat to seat.
- Why does my 11x26 room have one loud bass note?
- The short answer for this room: two of its dimensions reinforce the same note near 151.5 Hz. Bass unevenness like that is built into the shape of the room and shows up regardless of what speakers or sub you use.
- How do I fix bass problems in an 11x26 room?
- Put bass traps in the four floor-to-ceiling corners first, as thick as you can fit (6 to 12 in) plus a membrane trap tuned near 151.5 Hz, since that note's own quarter wavelength (about 1.8 ft) is too deep for any panel. From there, move your seat to about 9.9 ft from the front wall, then measure with REW below 148 Hz to see what still needs work.
Similar room sizes
How these numbers are calculated
Modes use the rectangular-room equation f = (c/2)·√((nx/L)² + (ny/W)² + (nz/H)²) with c = 343 m/s, for an empty room with rigid walls. The Schroeder frequency is fs = 2000 x sqrt(RT60 / V), assuming RT60 = 0.4 s. The modal score starts at 100 and subtracts penalties for stacked modes, density dips, gaps, proportions outside the Bolt area and dimension multiples. Doors, openings and furniture shift real rooms away from these values, which is what the room mode calculator and the 3D editor are for.