Start

Bowers & Wilkins 606 S3

600 Series

The Bowers & Wilkins 606 S3 is a bookshelf speaker with 8 Ω impedance and 88 dB sensitivity. Every receiver and amp in our catalogue can drive it.

Impedance
8 Ω
What the receiver must be rated for
Sensitivity
88 dB
Higher is louder per watt
Amplifier power
30–120 W
Bowers & Wilkins's recommendation
Bass extension
52 Hz
How low it plays

$1,200 a pair (MSRP, September 2026)

Check it with your receiverSee it in your room
3D model of the Bowers & Wilkins 606 S3

Drag to turn it. Built from the published dimensions, not a photo.

We earn a commission when you buy through these links. It never affects which products we show or recommend. Disclosure

Used on eBay

Which receivers and amps can drive it?

What decides it is impedance: the 606 S3 is 8 Ω, and the receiver or amp has to be rated for that.

  • Works

    Receivers and amps rated for 8 Ω

    29 in our catalogue

In its price range

All 29 receivers and amps we checked

Works29

Which center speaker matches it?

For the closest tonal match as voices move across the front, pick a center from the same 600 Series.

Plan your room around the 606 S3.

Draw your room in 3D, place the 606 S3 and see how they sound at your seat, with every connection to your receiver checked. Designing is free.

Build it in your room

606 S3 specifications

Impedance
8 Ω
Sensitivity
88 dB (2.83 V, 1 m)
Low end
52 Hz
Drivers
1 × 25 mm, 1 × 165 mm
Size
7×14×12 in
Recommended amplifier power
30–120 W
Weight
7.05 kg (15.5 lb)
MSRP
$1,200 a pair (MSRP, September 2026)

Every value comes from the sources under References, last retrieved September 15, 2026. To check it against the rest of your system, use the compatibility checker.

Questions about the 606 S3

What receiver do I need for the 606 S3?
One rated for 8 Ω speakers. In our catalogue, Denon AVR-S570BT, Emotiva BasX A-700 and Yamaha RX500A are rated to drive it.
Is the 606 S3 4 ohm or 8 ohm?
The Bowers & Wilkins 606 S3 has a nominal impedance of 8 Ω. Use a receiver or amplifier rated down to 8 Ω or lower.
How much power does the 606 S3 need?
Bowers & Wilkins recommends an amplifier of 30–120 W. Its sensitivity is 88 dB (2.83 V, 1 m). How much of that you use depends on how far you sit and how loud you listen, which the 3D editor works out for your room.
How low does the 606 S3 go?
The Bowers & Wilkins 606 S3 is rated down to 52 Hz. Below that, a subwoofer takes over; where the bass actually lands depends on your room's modes.
How big is the 606 S3?
The Bowers & Wilkins 606 S3 measures 189 × 344 × 300 mm (7.4 × 13.5 × 11.8 in, width × height × depth) and weighs 7.05 kg (15.5 lb).

Similar products

Side by side

References

  1. Bowers & Wilkins 606 S3: Spec sheet, bowerswilkins.com, retrieved September 15, 2026
  2. Bowers & Wilkins 606 S3: Manufacturer product page, bowerswilkins.com, retrieved September 15, 2026

Brand names are trademarks of their owners. Not affiliated with or endorsed by any manufacturer. 3D models are our approximations. Prices are manufacturer list prices (MSRP) as of the month shown. How we earn from buy links: affiliate disclosure.