Start

ELAC DF63

Debut 3.0 series

The ELAC DF63 is a tower speaker with 4 Ω impedance and 87.5 dB sensitivity. 28 of the 29 receivers and amps in our catalogue can drive it, 14 of them once set to 4 Ω.

Impedance
4 Ω
What the receiver must be rated for
Sensitivity
87.5 dB
Higher is louder per watt
Amplifier power
30–180 W
ELAC's recommendation
Bass extension
46 Hz
How low it plays

$649 each (MSRP, September 2026)

Check it with your receiverSee it in your room
3D model of the ELAC DF63

Drag to turn it. Built from the published dimensions, not a photo.

We earn a commission when you buy through these links. It never affects which products we show or recommend. Disclosure

Used on eBay

Which receivers and amps can drive it?

What decides it is impedance: the DF63 is 4 Ω, and the receiver or amp has to be rated for that.

  • Works

    Receivers and amps rated for 4 Ω

    14 in our catalogue

  • Needs a setting change

    Receivers with a 4 Ω setting

    Set the receiver to 4 Ω in its speaker setup.

    14 in our catalogue

  • Not recommended

    Receivers not rated for 4 Ω

    1 in our catalogue

In its price range

All 29 receivers and amps we checked

Works14

Needs a setting change14

Set the receiver to 4 Ω in its speaker setup.

Not recommended1

ELAC DF63 is 4 Ω; Denon AVR-S570BT supports 6 Ω and up.

Which center speaker matches it?

For the closest tonal match as voices move across the front, pick a center from the same Debut 3.0 series.

Plan your room around the DF63.

Draw your room in 3D, place the DF63 and see how they sound at your seat, with every connection to your receiver checked. Designing is free.

Build it in your room

DF63 specifications

Impedance
4 Ω
Sensitivity
87.5 dB (2.83 V, 1 m)
Low end
46 Hz
Drivers
1 × 25 mm, 2 × 165 mm, 1 × 165 mm
Size
8×43×11 in
Recommended amplifier power
30–180 W
Weight
17.6 kg (38.8 lb)
MSRP
$649 each (MSRP, September 2026)

Every value comes from the sources under References, last retrieved September 15, 2026. To check it against the rest of your system, use the compatibility checker.

Questions about the DF63

What receiver do I need for the DF63?
One rated for 4 Ω speakers. In our catalogue, Emotiva BasX A-700, Monoprice M7100X and Onkyo TX-NR6100 are rated to drive it. Yamaha RX500A, Denon AVR-S670H and Denon AVR-X1700H work once the receiver's impedance setting is changed to 4 Ω. Denon AVR-S570BT is not rated for it.
Is the DF63 4 ohm or 8 ohm?
The ELAC DF63 has a nominal impedance of 4 Ω. Use a receiver or amplifier rated down to 4 Ω or lower.
How much power does the DF63 need?
ELAC recommends an amplifier of 30–180 W. Its sensitivity is 87.5 dB (2.83 V, 1 m). How much of that you use depends on how far you sit and how loud you listen, which the 3D editor works out for your room.
How low does the DF63 go?
The ELAC DF63 is rated down to 46 Hz. Below that, a subwoofer takes over; where the bass actually lands depends on your room's modes.
How big is the DF63?
The ELAC DF63 measures 195 × 1094 × 268 mm (7.7 × 43.1 × 10.6 in, width × height × depth) and weighs 17.6 kg (38.8 lb).

Similar products

References

  1. ELAC DF63: Owner's manual, elac.com, retrieved September 15, 2026
  2. ELAC DF63: Retailer listing, worldwidestereo.com, retrieved September 15, 2026
  3. ELAC DF63: Retailer listing, headphones.com, retrieved September 15, 2026

Brand names are trademarks of their owners. Not affiliated with or endorsed by any manufacturer. 3D models are our approximations. Prices are manufacturer list prices (MSRP) as of the month shown. How we earn from buy links: affiliate disclosure.