Get started

KEF Q6 Meta

Center channel speaker · Q Series series

Drag to turn the model. It is built from the published dimensions, not a photo.

The KEF Q6 Meta is a 4 Ω center channel speaker rated 86 dB (2.83 V, 1 m), with a recommended 15–200 W amplifier. Of the 29 receivers and amps in our catalogue, 14 are rated to drive it, 14 work after an impedance setting change and 1 is not recommended.

$850 each (MSRP, September 2026)

Check it with your receiverSee it in your room

We earn a commission when you buy through these links. It never affects which products we show or recommend. Disclosure

Used on eBay

Receivers and amplifiers for the Q6 Meta

Each pairing is checked by our compatibility engine: the speaker's impedance against the amplifier's rated minimum, and height decoding for height speakers. Whether it plays loud enough depends on how far you sit, which the 3D editor works out for your room.

Rated to drive it (14)

Works after a setting change (14)

Set the receiver to 4 Ω in its speaker setup.

Not recommended (1)

KEF Q6 Meta is 4 Ω; Denon AVR-S570BT supports 6 Ω and up.

Q6 Meta specifications

Impedance4 Ω
Sensitivity86 dB (2.83 V, 1 m)
Low end63 Hz
Drivers1 × 19 mm, 1 × 100 mm, 2 × 165 mm
Size25×8×12 in
Recommended amplifier power15–200 W
Weight14.1 kg (31.1 lb)
MSRP$850 each (MSRP, September 2026)

Every value comes from the sources under References, last retrieved September 15, 2026. To check it against the rest of your system, use the compatibility checker.

Questions about the Q6 Meta

What receiver do I need for the Q6 Meta?
One rated for 4 Ω speakers. In our catalogue, Emotiva BasX A-700, Monoprice M7100X and Onkyo TX-NR6100 are rated to drive it. Yamaha RX500A, Denon AVR-S670H and Denon AVR-X1700H work once the receiver's impedance setting is changed to 4 Ω. Denon AVR-S570BT is not rated for it.
Is the Q6 Meta 4 ohm or 8 ohm?
The KEF Q6 Meta has a nominal impedance of 4 Ω. Use a receiver or amplifier rated down to 4 Ω or lower.
How much power does the Q6 Meta need?
KEF recommends an amplifier of 15–200 W. Its sensitivity is 86 dB (2.83 V, 1 m). How much of that you use depends on how far you sit and how loud you listen, which the 3D editor works out for your room.
How low does the Q6 Meta go?
The KEF Q6 Meta is rated down to 63 Hz. Below that, a subwoofer takes over; where the bass actually lands depends on your room's modes.
How big is the Q6 Meta?
The KEF Q6 Meta measures 629 × 210 × 303 mm (24.8 × 8.3 × 11.9 in, width × height × depth) and weighs 14.1 kg (31.1 lb).

Similar products

References

  1. KEF Q6 Meta: Spec sheet, assets.kef.com, retrieved September 15, 2026
  2. KEF Q6 Meta: Manufacturer product page, us.kef.com, retrieved September 15, 2026

Brand names are trademarks of their owners. Not affiliated with or endorsed by any manufacturer. 3D models are our approximations. Prices are manufacturer list prices (MSRP) as of the month shown. How we earn from buy links: affiliate disclosure.