Get started

MartinLogan Motion XT F100

Tower speaker · Motion XT series

Drag to turn the model. It is built from the published dimensions, not a photo.

The MartinLogan Motion XT F100 is a 4 Ω tower speaker rated 92 dB, with a recommended 20–450 W amplifier. Of the 29 receivers and amps in our catalogue, 14 are rated to drive it, 14 work after an impedance setting change and 1 is not recommended.

$2,500 each (MSRP, September 2026)

Check it with your receiverSee it in your room

We earn a commission when you buy through these links. It never affects which products we show or recommend. Disclosure

Used on eBay

Receivers and amplifiers for the Motion XT F100

Each pairing is checked by our compatibility engine: the speaker's impedance against the amplifier's rated minimum, and height decoding for height speakers. Whether it plays loud enough depends on how far you sit, which the 3D editor works out for your room.

Rated to drive it (14)

Works after a setting change (14)

Set the receiver to 4 Ω in its speaker setup.

Not recommended (1)

MartinLogan Motion XT F100 is 4 Ω; Denon AVR-S570BT supports 6 Ω and up.

Motion XT F100 specifications

Impedance4 Ω
Sensitivity92 dB
Low end31 Hz
Drivers1 × 32 mm, 1 × 165 mm, 3 × 165 mm
Size13×48×15 in
Recommended amplifier power20–450 W
Weight34.5 kg (76.1 lb)
MSRP$2,500 each (MSRP, September 2026)

Every value comes from the sources under References, last retrieved September 15, 2026. To check it against the rest of your system, use the compatibility checker.

Questions about the Motion XT F100

What receiver do I need for the Motion XT F100?
One rated for 4 Ω speakers. In our catalogue, Emotiva BasX A-700, Monoprice M7100X and Onkyo TX-NR6100 are rated to drive it. Yamaha RX500A, Denon AVR-S670H and Denon AVR-X1700H work once the receiver's impedance setting is changed to 4 Ω. Denon AVR-S570BT is not rated for it.
Is the Motion XT F100 4 ohm or 8 ohm?
The MartinLogan Motion XT F100 has a nominal impedance of 4 Ω. Use a receiver or amplifier rated down to 4 Ω or lower.
How much power does the Motion XT F100 need?
MartinLogan recommends an amplifier of 20–450 W. Its sensitivity is 92 dB. How much of that you use depends on how far you sit and how loud you listen, which the 3D editor works out for your room.
How low does the Motion XT F100 go?
The MartinLogan Motion XT F100 is rated down to 31 Hz. Below that, a subwoofer takes over; where the bass actually lands depends on your room's modes.
How big is the Motion XT F100?
The MartinLogan Motion XT F100 measures 318 × 1213 × 381 mm (12.5 × 47.8 × 15 in, width × height × depth) and weighs 34.5 kg (76.1 lb).

Similar products

References

  1. MartinLogan Motion XT F100: Spec sheet, martinlogan.com, retrieved September 15, 2026
  2. MartinLogan Motion XT F100: Retailer listing, audioadvice.com, retrieved September 15, 2026

Brand names are trademarks of their owners. Not affiliated with or endorsed by any manufacturer. 3D models are our approximations. Prices are manufacturer list prices (MSRP) as of the month shown. How we earn from buy links: affiliate disclosure.