Start

Polk Signature Elite ES90

Signature Elite series

The Polk Signature Elite ES90 is a height speaker with 4 Ω impedance and 85 dB sensitivity. 27 of the 29 receivers and amps in our catalogue can drive it, 13 of them once set to 4 Ω.

Impedance
4 Ω
What the receiver must be rated for
Sensitivity
85 dB
Higher is louder per watt
Amplifier power
20–150 W
Polk's recommendation
Bass extension
142 Hz
How low it plays

$449 a pair (MSRP, September 2026)

Check it with your receiverSee it in your room
3D model of the Polk Signature Elite ES90

Drag to turn it. Built from the published dimensions, not a photo.

We earn a commission when you buy through these links. It never affects which products we show or recommend. Disclosure

Used on eBay

Which receivers and amps can drive it?

What decides it is impedance: the Signature Elite ES90 is 4 Ω, and the receiver or amp has to be rated for that, and as a height speaker it needs Dolby Atmos or DTS:X decoding.

  • Works

    Receivers and amps rated for 4 Ω

    14 in our catalogue

  • Needs a setting change

    Receivers with a 4 Ω setting

    Set the receiver to 4 Ω in its speaker setup.

    13 in our catalogue

  • Not recommended

    Receivers without Dolby Atmos or DTS:X

    A height speaker needs one that decodes them.

    2 in our catalogue

In its price range

All 29 receivers and amps we checked

Works14

Needs a setting change13

Set the receiver to 4 Ω in its speaker setup.

Not recommended2

  • Denon AVR-S570BT

    Polk Signature Elite ES90 is 4 Ω; Denon AVR-S570BT supports 6 Ω and up.

  • Denon AVR-S670H

    Denon AVR-S670H has no Dolby Atmos or DTS:X decoding for height speakers.

Plan your room around the Signature Elite ES90.

Draw your room in 3D, place the Signature Elite ES90 and see how they sound at your seat, with every connection to your receiver checked. Designing is free.

Build it in your room

Signature Elite ES90 specifications

Impedance
4 Ω
Sensitivity
85 dB
Low end
142 Hz
Drivers
1 × 25 mm, 1 × 133 mm
Size
7×7×12 in
Recommended amplifier power
20–150 W
Weight
3.76 kg (8.3 lb)
MSRP
$449 a pair (MSRP, September 2026)

Every value comes from the sources under References, last retrieved September 15, 2026. To check it against the rest of your system, use the compatibility checker.

Questions about the Signature Elite ES90

What receiver do I need for the Signature Elite ES90?
One rated for 4 Ω speakers. In our catalogue, Emotiva BasX A-700, Monoprice M7100X and Onkyo TX-NR6100 are rated to drive it. Yamaha RX500A, Denon AVR-X1700H and Denon AVR-S770H work once the receiver's impedance setting is changed to 4 Ω. Denon AVR-S570BT and Denon AVR-S670H are not rated for it.
Is the Signature Elite ES90 4 ohm or 8 ohm?
The Polk Signature Elite ES90 has a nominal impedance of 4 Ω. Use a receiver or amplifier rated down to 4 Ω or lower.
How much power does the Signature Elite ES90 need?
Polk recommends an amplifier of 20–150 W. Its sensitivity is 85 dB. How much of that you use depends on how far you sit and how loud you listen, which the 3D editor works out for your room.
How low does the Signature Elite ES90 go?
The Polk Signature Elite ES90 is rated down to 142 Hz. Below that, a subwoofer takes over; where the bass actually lands depends on your room's modes.
How big is the Signature Elite ES90?
The Polk Signature Elite ES90 measures 186 × 189 × 306 mm (7.3 × 7.4 × 12 in, width × height × depth) and weighs 3.76 kg (8.3 lb).

Similar products

References

  1. Polk Signature Elite ES90: Spec sheet, polkaudio.com, retrieved September 15, 2026
  2. Polk Signature Elite ES90: Manufacturer product page, polkaudio.com, retrieved September 15, 2026

Brand names are trademarks of their owners. Not affiliated with or endorsed by any manufacturer. 3D models are our approximations. Prices are manufacturer list prices (MSRP) as of the month shown. How we earn from buy links: affiliate disclosure.