What receiver do I need for the Prime Elevation?

One rated for 8 Ω speakers. In our catalogue, Emotiva BasX A-700, Yamaha RX500A and Denon AVR-X1700H are rated to drive it. Denon AVR-S570BT and Denon AVR-S670H are not rated for it.

Is the Prime Elevation 4 ohm or 8 ohm?

The SVS Prime Elevation has a nominal impedance of 8 Ω. Use a receiver or amplifier rated down to 8 Ω or lower.

How much power does the Prime Elevation need?

SVS recommends an amplifier of 20–150 W. Its sensitivity is 87 dB (2.83 V, 1 m). How much of that you use depends on how far you sit and how loud you listen, which the 3D editor works out for your room.

How low does the Prime Elevation go?

The SVS Prime Elevation is rated down to 55 Hz. Below that, a subwoofer takes over; where the bass actually lands depends on your room's modes.

How big is the Prime Elevation?

The SVS Prime Elevation measures 138 × 235 × 200 mm (5.4 × 9.3 × 7.9 in, width × height × depth) and weighs 3.5 kg (7.7 lb).

SVS Prime Elevation

Prime series

The SVS Prime Elevation is a height speaker with 8 Ω impedance and 87 dB sensitivity. 27 of the 29 receivers and amps in our catalogue can drive it.

Impedance

8 Ω

What the receiver must be rated for

Sensitivity

87 dB

Higher is louder per watt

Amplifier power

20–150 W

SVS's recommendation

Bass extension

55 Hz

How low it plays

$275 each (MSRP, September 2026)

Check it with your receiver See it in your room

Drag to turn it. Built from the published dimensions, not a photo.

We earn a commission when you buy through these links. It never affects which products we show or recommend. Disclosure

Used on eBay

Which receivers and amps can drive it?

What decides it is impedance: the Prime Elevation is 8 Ω, and the receiver or amp has to be rated for that, and as a height speaker it needs Dolby Atmos or DTS:X decoding.

Works
Receivers and amps rated for 8 Ω
27 in our catalogue
Not recommended
Receivers without Dolby Atmos or DTS:X
A height speaker needs one that decodes them.
2 in our catalogue

In its price range

All 29 receivers and amps we checked

Works27

Emotiva BasX A-700
7 channels · 110 W at 8 Ω
Yamaha RX500A
7 amplified channels · 70 W at 8 Ω
Denon AVR-X1700H
7 amplified channels · 80 W at 8 Ω
Monoprice M7100X
7 channels · 90 W at 8 Ω
Denon AVR-S770H
7 amplified channels · 75 W at 8 Ω
Onkyo TX-NR6100
7 amplified channels · 100 W at 8 Ω
Yamaha RX-V6A
7 amplified channels · 100 W at 8 Ω
Crown XLS 1502
2 channels · 300 W at 8 Ω
Denon AVR-X1800H
7 amplified channels · 80 W at 8 Ω
Denon AVR-S970H
7 amplified channels · 90 W at 8 Ω
Onkyo TX-RZ30
9 amplified channels · 100 W at 8 Ω
Pioneer VSX-LX305
9 amplified channels · 100 W at 8 Ω
Onkyo TX-NR7100
9 amplified channels · 100 W at 8 Ω
Marantz Cinema 70s
7 amplified channels · 50 W at 8 Ω
Denon AVR-X2900H
7 amplified channels · 95 W at 8 Ω
Pioneer VSX-LX505
9 amplified channels · 120 W at 8 Ω
Emotiva XPA-2 Gen3
2 channels · 300 W at 8 Ω
Onkyo TX-RZ50
9 amplified channels · 120 W at 8 Ω
Denon AVR-X3800H
9 amplified channels · 105 W at 8 Ω
Denon AVR-X3900H
9 amplified channels · 105 W at 8 Ω
Monoprice Monolith 7X
7 channels · 200 W at 8 Ω
Emotiva XPA-5 Gen3
5 channels · 250 W at 8 Ω
Denon AVR-X4800H
9 amplified channels · 125 W at 8 Ω
Marantz Cinema 50
9 amplified channels · 110 W at 8 Ω
Denon AVR-X6800H
11 amplified channels · 140 W at 8 Ω
ATI AT525NC
5 channels · 200 W at 8 Ω
Parasound Halo A 21+
2 channels · 300 W at 8 Ω

Not recommended2

Denon AVR-S570BT
Denon AVR-S570BT has no Dolby Atmos or DTS:X decoding for height speakers.
Denon AVR-S670H
Denon AVR-S670H has no Dolby Atmos or DTS:X decoding for height speakers.

Plan your room around the Prime Elevation.

Draw your room in 3D, place the Prime Elevation and see how they sound at your seat, with every connection to your receiver checked. Designing is free.

Build it in your room

Prime Elevation specifications

Impedance: 8 Ω
Sensitivity: 87 dB (2.83 V, 1 m)
Low end: 55 Hz
Drivers: 1 × 25 mm, 1 × 114 mm
Size: 5×9×8 in
Recommended amplifier power: 20–150 W
Weight: 3.5 kg (7.7 lb)
MSRP: $275 each (MSRP, September 2026)

Every value comes from the sources under References, last retrieved September 15, 2026. To check it against the rest of your system, use the compatibility checker.

Questions about the Prime Elevation

What receiver do I need for the Prime Elevation?: One rated for 8 Ω speakers. In our catalogue, Emotiva BasX A-700, Yamaha RX500A and Denon AVR-X1700H are rated to drive it. Denon AVR-S570BT and Denon AVR-S670H are not rated for it.
Is the Prime Elevation 4 ohm or 8 ohm?: The SVS Prime Elevation has a nominal impedance of 8 Ω. Use a receiver or amplifier rated down to 8 Ω or lower.
How much power does the Prime Elevation need?: SVS recommends an amplifier of 20–150 W. Its sensitivity is 87 dB (2.83 V, 1 m). How much of that you use depends on how far you sit and how loud you listen, which the 3D editor works out for your room.
How low does the Prime Elevation go?: The SVS Prime Elevation is rated down to 55 Hz. Below that, a subwoofer takes over; where the bass actually lands depends on your room's modes.
How big is the Prime Elevation?: The SVS Prime Elevation measures 138 × 235 × 200 mm (5.4 × 9.3 × 7.9 in, width × height × depth) and weighs 3.5 kg (7.7 lb).

References

Brand names are trademarks of their owners. Not affiliated with or endorsed by any manufacturer. 3D models are our approximations. Prices are manufacturer list prices (MSRP) as of the month shown. How we earn from buy links: affiliate disclosure.